When your door won’t open even though it’s unlocked, one of the bolts has failed to withdraw. The key turns, the lock disengages, and yet the door stays firmly shut, because a hook, a roller or a deadbolt remains sitting in the frame. On a uPVC or composite door that almost always points at the multipoint mechanism. On a timber door it usually points at the latch or the frame itself.
Whatever you do, stop forcing it. A jammed door that somebody shoulders or levers turns a repairable fault into a broken frame, and the repair bill grows accordingly.
First, work out what the door is telling you
Stand at the door and run through these questions. The answers narrow the cause quickly.
- Does the handle lift normally? If it lifts with no resistance at all, the gearbox has probably snapped.
- Does the handle refuse to lift? Something is binding, either a bolt under pressure or a seized mechanism.
- Does the key turn freely through its full travel? Free rotation with nothing happening suggests the cylinder cam no longer drives the mechanism.
- Can you hear the bolts moving? Listen along the edge of the door as you operate the handle.
- Does the door move at all in the frame? A door that rattles slightly but will not swing usually has one bolt still engaged.
The most common causes
A snapped multipoint gearbox
This causes more stuck doors than anything else we attend. The gearbox translates the handle lift into bolt movement. When the internal cam or spring breaks, the bolts stay where they last sat, which is quite often extended. The handle then flops uselessly and the door will not release.
You cannot fix this from outside. We manipulate the mechanism to withdraw the bolts, then fit a new gearbox.
A dropped or swollen door
If the door has sagged on its hinges, the bolts sit under load inside the keeps. Even with the lock disengaged, friction holds everything in place. Warm weather makes it worse, because uPVC expands and presses the door harder into the frame.
Try this before anything else. Lift the handle while pulling the door firmly towards you, or push it inwards, to take the weight off the bolts. Many doors release immediately once the pressure comes off.
A failed cylinder cam
The small tab on the back of the euro cylinder drives the mechanism. When it shears or wears round, your key spins freely and the mechanism never moves. The lock feels unlocked, because in a sense it is, but nothing has actually retracted.
A jammed hook, roller or deadbolt
Dirt, grit and dried-out lubricant build up in the keeps over years. A single hook that cannot retract holds the whole door. This one sometimes frees itself with a spray of dry PTFE lubricant along the door edge and a few operations of the handle.
A frozen or seized lock
Cold snaps catch people out. Moisture inside a mechanism freezes, and the parts will not move. Warm the lock gently with your hands or a warm cloth. Never pour boiling water over a uPVC door and never apply a naked flame, because both crack the frame and damage the seals.
A latch problem on a timber door
Timber doors swell in damp weather and the latch binds in the striking plate. The door then refuses to open despite an unlocked lock. Press the door towards the hinges while turning the handle, which relieves the pressure on the latch.
A failed thumbturn or child lock
Some doors have a secondary internal lock, a thumbturn or a snib that overrides the main lock. If somebody has engaged it, the main lock reads as unlocked while the door stays secured.
What to try before you call
Work through these in order, gently.
- Take the weight off. Pull or push the door firmly while operating the handle, so the bolts sit free of load.
- Lift and hold. Lift the handle fully and hold it up while you turn the key and pull.
- Try the key in both directions. Some mechanisms need a full turn past the stop before the bolts retract.
- Lubricate the edge. Spray dry PTFE or graphite along the visible bolts and into the keeps. Avoid oil and avoid WD-40.
- Check the other doors. If you can get outside safely, you may be able to work on the door from the other side, which helps enormously.
- Stop if anything resists hard. Forcing bends hooks, snaps spindles and cracks frames.
If none of that works, call us. Our emergency locksmith service covers this exact situation around the clock.
When it becomes urgent
Treat the situation as an emergency and call immediately if any of these apply:
- Somebody is trapped inside, particularly a child, an older person or anyone unwell
- The stuck door is your only exit, which creates a serious fire risk
- The door has jammed open and you cannot secure the property
- You smell gas, see smoke, or face any other hazard behind the door
A door that will not open is a fire safety problem as much as an inconvenience. Do not leave it until the weekend. If a door has jammed open and you need the property secured tonight, our boarding up service covers that too.
How we get you through it
We nearly always open these doors without damage. We manipulate the multipoint mechanism to release the bolts, which leaves the door and frame untouched, and then we deal with the underlying fault.
Once the door opens, we diagnose properly. Sometimes the answer is a new gearbox. Sometimes it is a hinge adjustment and a clean, which costs far less. We will tell you which, and we will not sell you a mechanism you do not need. We carry common gearboxes, cylinders and handle sets, so most repairs finish in the same visit. See our door lock services for the full range.
Why doors jam when they do
We get two clear spikes in these call-outs. The first arrives with the first proper cold snap, when moisture in tired mechanisms freezes and brittle components give up. The second arrives in high summer, when uPVC expands and a door that was already sitting low binds hard in its frame.
Coastal homes across Bournemouth, Poole and Christchurch suffer more than most, because salt air corrodes the springs and cams inside the mechanism. Regular maintenance genuinely helps. Twice a year, wipe the bolts clean, apply a dry lubricant, and check that the door still closes without you having to lift or shove it. The Door and Hardware Federation publishes further guidance on maintaining door hardware.
Stuck door? Call JCarter Locksmiths
We will open it without damage wherever possible, then fix the cause. Available 24/7 across Bournemouth, Poole, Christchurch and the surrounding areas:
- Jammed uPVC, composite and timber doors opened non-destructively
- Multipoint gearboxes, cylinders and handles replaced
- Doors realigned so the fault does not return
- Free, upfront quotes with no call-out fee
- Family-run, military veteran-owned, hundreds of five-star reviews
Call or WhatsApp us on 07842 252 025. See our locked out service or request a free quote.
Frequently asked questions
Why won’t my door open when the lock is clearly unlocked?
One of the multipoint bolts has failed to retract, usually because the gearbox has broken or the door has dropped and trapped a bolt under load. The lock and the bolts are separate things.
Should I force the door open?
No. Forcing bends the hooks, snaps the spindle and often cracks the frame, which turns a straightforward repair into an expensive one.
Can a locksmith open it without damaging the door?
Usually, yes. We manipulate the mechanism to release the bolts, which leaves the door and frame intact.
My door only jams in hot weather, why?
uPVC expands in heat and presses the door harder into the frame. A small hinge adjustment normally cures it for good.
How long does the repair take?
Opening the door takes minutes in most cases. Replacing a gearbox afterwards adds around an hour, and we usually complete both in one visit.